The majority of heaters need at least one dedicated circuit. Many homeowners prefer to let electricians handle this work.
Prior to installing a brand new electric heater, turn off any power source to the existing outlets in your breaker panel and drain the tank. Set up the heater.
Electric wall heaters need the installation of a new circuit. make sure that an electrician flies cables from your breaker panel to the opening in the wall where studs are. The wire should be 14 gauge and a ground that's proportional for the heater's wattage must be utilized.
Electricity
Connecting the heater's electrical supply to your home is a part of installing it. Follow the electric heater instructions attentively, then have an electrician set up a new circuit breaker and fish cable in your wall heater's location ensure that the circuit you choose to install has the capacity to accommodate your heater's power consumption.
Be sure to turn off all nearby circuits before the work begins. This can prevent electrocution. Don't cut any existing wiring or pipes as you are cutting the drywall. If you're installing a new outlet too, be sure to use a stud finder to verify that the spacing of studs and their location are correct prior to cutting.
The National Electrical Code allows you to install an electric heater baseboard, without outlet. But the code requires outlets at least every 12 feet for walls. If you're installing an ganged electrical heater (two or more of them connected on one circuit) it is important to ensure that each heater is the same wattage. In the event that they are not, the mix could be too much for the system. Examine each of the heaters with an Ohm Meter before you plug it in.
The Plumbing
Connecting the heater to the pipes, fitting the temperature and pressure relief valves as well as the discharge lines (if necessary as required by codes), as well as installing the thermal expansion tank. A good plumber will be acquainted with the particulars of every city, and will make sure all is done in accordance with the law. This will help prevent problems such as carbon monoxide leaks which can be dangerous homeowners have to handle.
The plumber joins the pipes with copper tubing as well as a soldering iron. The new pipes are connected to the hot and cold water intakes in the middle of the tank. If your heater is powered by gas, the plumber will also have to connect a gas line to bring the fuel in. A plumber certified to provide gas-powered plumbing can complete this task. The plumber also needs to install a gas shut-off valve and gas line vent.
The majority of people do not have the equipment to safely handle this kind of work themselves We recommend that you leave every plumbing project to skilled plumbers. Despite the best intentions, DIY tasks related to water heaters may be hazardous. If a gas-powered water heater is not installed correctly this could lead to dangerous carbon monoxide poisoning.
They'll never fail to deliver on the promises of their excellent service and be upfront about the costs they will charge. You will be kept informed throughout the project to ensure you don't have to be surprised by the time to pay. This level of honesty and client service is the standard every Legacy Plumbing technician strives to achieve with each and every heater installation.
Ventilation
There is a need to vent your heater unless you intend to put it on the ceiling. This can be a fairly simple or very complex process based on the type of heater as well as the ventilation system you have. For determining which technique is best for you, follow the instruction manual provided by your heater manufacturer.
A majority of natural gas heaters employ an atmospheric vent system. The exhaust, which can be hazardous carbon monoxide that comes from your heater, can rise through a chimney-style flue.
The venting system may need to be changed into direct-vent, power-vent or another system. It is best to leave the installation to the experts.
Take off the vent pipe that is on side of the heater. Remove it. Connect a fresh temperature and pressure relief valve. The valve must be big enough for the pipe to flow up and around it. To connect this duct, solder a copper fitting onto one end of the pipe. It must be designed to meet the requirements of the required pressure and temperature of the heater.
Attach the duct to the valve you are replacing and fix it with a screw. Take a measurement of the distance between the elbow of the 90 degree duct, to the end of it that is suspended off the rafter. You will need to purchase the correct length of conduit.
Set up the ducting as well as a cap for the external part of the pipe. Check that the air flow of the heater is not restricted after the ducting has been put into place. This could lead to the possibility of a fire, explosion or CO poisoning.
If you want to make sure that the gas heating installation venting system is up to code, local codes may require a professional plumber to review the installation after it is completed and certify that you've got a properly installation. This inspection can help to avoid expensive repairs later on when your heater's venting does not meet standards.
Maintenance
The majority of heating system problems are due to the lack of maintenance for the heater after installation. Regularly performing preventive measures for example, like collecting megohm measurements, and examining for corrosion or scaling, can help to keep your home warm during the winter.
To ensure that you do not have problems, it is important that the wiring for your heater is in line with National Electric Code (NEC) standards and guidelines. It's also a great idea to ensure that the wires have a minimal temperatures of 200 degrees Celsius or greater. Heating the heaters for a few hours before the installation in order to improve resistance will enhance the efficiency of the unit and decrease the chance of failures later.
There are many heating systems that have drafts to bring combustion fumes into the flue. It is possible for this draft to malfunction, allowing dangerous carbon monoxide gases to get into the home. The addition of a draft hood and checking that the venting system working properly can help to stop this from being a reality.
A regular cleaning of the tank and heater could be beneficial in reducing the requirement for repairs at some point in the future. To ensure optimal performance, this process includes removing any dirt from the tank or burner's surfaces. Cleanliness of the heater will increase the efficiency of your heater, saving you some money in the long run.
In recognizing the indicators warning signs that your heater may be beginning to break down, you will be able to get a replacement in time and avoid costly repairs that will be required in the near future. Aiello's experienced technicians can install the most comprehensive heater and will keep you comfortable all through winter.